In the pulp industry, digesters are used to disolve lignin in wood chips. The concentration of lignin is measured and is called the Kappa number. In this thesis, the question of whether an online Kappa sensor, taking samples from the mid-phase of the digester, is useful or not is analyzed. For the samples to be useful, there has to be a relationship between the measured Kappa at the mid- phase and the measured Kappa in the blowpipe at the bottom of the digester. An ARX model of the lower part of the digester has been estimated.

One of Sweden?s sixteen national environmental objectives strives to decrease the impact on the climate. By 2020, green house gas emissions should be 40 % less compared to the levels of 1990 and a minimum of 50 % of the energy consumption should come from renewable energy sources. Because of this there is a great need of increasing the production of renewable energy. This is where biogas comes in as a competitive alternative.

The Swedish pulp and paper industry meets higher demand for energy efficiencyi mprovements with increasing energy prices and changes in the Swedish renewable energy certificate system. One action of energy efficiency improvement is by using secondary heat, that otherwise would have been treated as waste heat, for use in a system with lower temperature demands. The aim of this Master´s thesis is to identify possible secondary heat sources in a typical Swedish pulp and paper mill and to investigate what economic benefits the secondary heat will provide when being used for pre heating of wood chips to a kraft digester.The Master´s thesis focuses on three secondary heat sources; dry warm air, warm water and moisture saturated warm air located inside the pulp or paper mill. Two types of kraft digesters are simulated within this study, a typical Scandinavian digester and a modern twin vessel steam phase digester.Due to quality aspects and low temperature level drying is the drying technology with dry warm air rejected. Using warm water in direct contact with wood chips increases the quantity of water to the evaporation plant and thus reduced pulp or paper production and is therefore also rejected.

In industrial control systems PID-control remains the prevalent strategy, also for processes that would benefit from model based control. The purpose of this thesis is to evaluate whether model based control can be readily implemented in an industrial control system. To this end a simulated surge tank with a simulated industrial control system is studied. For evaluation two scenarios with specified objectives are selected.Following a review of LQR and versions of MPC, Predictive Functional Control (PFC) is considered the most suitable for implementation. PFC is a form of MPC developed with industrial applications in mind and therefore has several advantages for implementation in an industrial control system.

Title: Co-operative, prevent or complement? - An essay on the relationships between control systems. Authors: Kim Eriksson and Victoria KarlssonPurpose: The essay aims to describe the relations between control systems and how they related to each other, based on an operationalization of the control systems. Research question: What are the control systems relations to each other? With regards whether control systems co-operative, prevents and/or complement each other.Theoretical framework: The essays theoretical framework is based on Malmi and Browns (2008) description of five different control systems and control mechanisms associated with each control system.   Research methodology: The method was based on three different data collection methods. These methods were observations, documentation, and semi-structured interviews.Conclusions: It is concluded that the control systems has comprehensive relations. Control systems have more, than one, relation to each other..

At the Skoghall pappermill, sulphatepaper pulp is produced in a continuous digester originally from 1969. To be able to maintain a high level of production there is a need for a process with few disturbances. Variations in how well the wooden chips are packed in the digester is one form of disturbance. Today there are no available measurements on how well the chips are packed. Instead this is regarded as being constant.

The secondary control must be part of the production plan, since the capacity will bedeployed in advance, just as the primary control. The activation of the new frequencycontrol should be preformed in Vattenfall's operations centers (DC) to minimizecommunication delay. Vattenfall needs to work towards a more holistic optimizationsystem. The main issue for Vattenfall Generation is not how we produce but ratherwhen, which is done with creation of bids. This is where there is the mostopportunity for improvement.

Studier har visat att det finns ett samband mellan syskonplacering och locus of control, medan andra studier inte funnit något samband. Syftet med denna studie är att undersöka relationen mellan syskonplacering, kön och locus of control ur ett hälsoperspektiv hos gymnasieelever i årskurs 3. I undersökningen deltog 147 gymnasielever ifrån fem skolor i Kronobergs län. Resultatet visade att kön och syskonplacering samvarierade med intern health locus of control (F= 3,01;p< 0,03; ES= 6,2) och att syskonplacering och kön tillsammans inte visade någon signifikant inverkan på extern health locus of control (F= 2,20;p=<0,09; ES= 4,6). Fyndet kan indikera att manliga mellanbarn i större utsträckning strävar efter en intern health locus of control än kvinnliga mellanbarn.Nyckelord: Syskonplacering, health locus of control, intern- och extern locus of control, kön..

This thesis aims to develop a control system for measuring electromagnetic compability (EMC). This has meant that a controller designed around an ATmega8 microcontroller has been manufactured and programmed. It has also meant the development of a comprehensive control software in the program MATLAB. The control system has been tested with satisfactory results and can now, monitor and control measurements of the EMC-type..

Title: Co-operative, prevent or complement? - An essay on the relationships between control systems. Authors: Kim Eriksson and Victoria KarlssonPurpose: The essay aims to describe the relations between control systems and how they related to each other, based on an operationalization of the control systems. Research question: What are the control systems relations to each other? With regards whether control systems co-operative, prevents and/or complement each other.Theoretical framework: The essays theoretical framework is based on Malmi and Browns (2008) description of five different control systems and control mechanisms associated with each control system.   Research methodology: The method was based on three different data collection methods. These methods were observations, documentation, and semi-structured interviews.Conclusions: It is concluded that the control systems has comprehensive relations. Control systems have more, than one, relation to each other..

Title: Co-operative, prevent or complement? - An essay on the relationships between control systems. Authors: Kim Eriksson and Victoria KarlssonPurpose: The essay aims to describe the relations between control systems and how they related to each other, based on an operationalization of the control systems. Research question: What are the control systems relations to each other? With regards whether control systems co-operative, prevents and/or complement each other.Theoretical framework: The essays theoretical framework is based on Malmi and Browns (2008) description of five different control systems and control mechanisms associated with each control system.   Research methodology: The method was based on three different data collection methods. These methods were observations, documentation, and semi-structured interviews.Conclusions: It is concluded that the control systems has comprehensive relations. Control systems have more, than one, relation to each other..

This thesis aims to develop a control system for measuring electromagnetic compability (EMC). This has meant that a controller designed around an ATmega8 microcontroller has been manufactured and programmed. It has also meant the development of a comprehensive control software in the program MATLAB. The control system has been tested with satisfactory results and can now, monitor and control measurements of the EMC-type..

The control of indoor temperature must be able to handle large time constants and both measureable disturbances like outdoor temperature, and non-measurable disturbances, like waste heat from appliances. Due to cheaper microcontrollers (small computers with designated tasks) with better performance, more advanced and computation-demanding methods for control can be used.In this thesis, Generalized Predictive Control (GPC) has been implemented and tested on a theoretically derived model of a house. GPC states that a model of the system is estimated in every sample, and the control is carried out simultaneously, based on predictions of the model. Disturbances like solar radiation can be estimated and used in the control as well. The control signals are determined by quadratic programming, which makes it possible to consider conditions, for example limitations on the control signals.GPC requires a number of parameters to be defined, like model order and control signal penalty, but is relatively robust for variations in them.

The purpose with this paper is that trough a description of the management control at Jitech AB find out if traditional management control have been abandoned for benefit for modern management control and in which extent the transition have happened. Further is the second purpose with this paper to find out which decisions that lies behind the design of the management control and how these are in opposition to with the theory..

This thesis has been conducted at Saab Bofors Dynamics AB. The purpose was to investigate if a non-linear missile model could be stabilized when the optimal control signal is computed considering constraints on the control input. This is particularly interesting because the missile is controlled with rudders that have physical bounds. This strategy is called Model Predictive Control. Simulations are conducted to compare this strategy with others; firstly simulations with step responses and secondly simulations when the missile is supposed to hit a moving target.